ASTM D1621 FREE DOWNLOAD

The minimum height shall be Rigid foams are typically used in the construction industry as sound and thermal insulation. It is obtained by pooling the within-laboratory standard deviations of the test results from all of the participating laboratories. They are designed with standard and optional features that increase testing efficiency and improve the testing experience for the operator. Glossary of Materials Testing Terms. Select from list below:

astm d1621

Uploader: Shaktitaur
Date Added: 4 June 2012
File Size: 9.50 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 76236
Price: Free* [*Free Regsitration Required]

The accuracy of the displacement measurement transducer shall be awtm Any test specimen preparation, conditioning, dimensions, or testing parameters, or a combination thereof, covered in the materials specification shall take precedence over those mentioned in this test method. This compliance can be measured then, if determined to be signi?

ASTM D1621-16 Compressive Properties of Rigid Cellular Plastics

Stop the crosshead and return to the pre-test location. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Link to Active This link will always route to the current Active version of the standard. Swivel seating can be placed on the platen attached to the d621 base or load cell in the moving crosshead.

astm d1621

Users of this test method should apply the principles outlined in Practice E to generate data speci? Email addresses must contain the symbol. The test specimens are centered between two compression platens photo below left and load is applied at a constant crosshead or actuator rate. The challenges of testing to this standard are: Current edition approved April 1, Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

  BASS SULTAN HENGZT MEIN ENGEL FREE DOWNLOAD

The data in Table 1 should not be applied to acceptance or rejection of materials, as these data apply only to the materials tested in the round robin and are unlikely to be rigorously representative of other lots, formulations, conditions, materials, or laboratories.

After testing and analysis, compressive strength, modulus and deformation at maximum load are reported.

ASTM D – 00 Standard Test Method for Compressive Properties Of Rigid Cellular Plastics

Suitable systems for this application include Series and Series electromechanical testing machines equipped with compression platens.

Each laboratory obtained six test results for each material. Such applications require additional tests such as impact, creep, and fatigue. We use cookies astn improve your browsing experience. For each material, all of the samples were prepared at one source, but the individual specimens were prepared at the laboratories that tested asgm. It is obtained by pooling the within-laboratory standard deviations of the test results from all of the participating laboratories.

The testing machine shall also include the following: Concrete, Asphalt and Rock.

ASTM D1621 – Compression Testing of Rigid Cellular Plastics

Next Checking to see if you are a returning visitor…. Specimens that fail at some obvious?

  ISENSEVEN LETS GO GET LOST FREE DOWNLOAD

astm d1621

Individual reprints single or multiple copies of this standard may be obtained by contacting D161 at the above address or at phonefaxor service astm. This measurement is made through use of the test machine crosshead drive system or using a direct measurement of compression platen displacement.

Plastics Testing Solutions Brochure The Plastics Testing Solutions brochure is a page, applications-focused, and standards-based brochure.

astm d1621

They are designed with standard and optional features that increase testing efficiency and improve the testing experience for the operator.

When a slidingcaliper gage is employed, the proper setting shall be that point at which the measuring faces of the gage contact the surfaces of the specimen without compressing them. These plates shall be larger than the specimen loading surface to ensure that the specimen loading is uniform. Please confirm that you agree with our privacy and cookies policy to submit this form.

All data that are to be compared should be obtained using common test conditions. Bluehill Universal Brochure Bluehill Universal Software is built from the ground-up for touch interaction and an intuitive user experience. Measure all distances for deformation or strain calculations from this point.